"TEXT'ILE

1. Two screens are coated with emulsion and exposed to UV for 2min 15sec and then pressure washed.
2. Shirts are ironed and then 1 color screen printed on front and back of garment. (Speedball fabric ink)
3. Shirts are run through the washer and dryer, and then touched up with a fine tip fabric marker.
4. VINYL CUT LENTICULAR lining is prepared.
5. Lenticulars are cut by hand to size.
6. Fabric lining is then glued, clamped and left to cure for 24 hrs.
7. EXCESS GLUE is removed from LENTICULARS.
8. Lenticulars are glued and clamped onto shirts and left to cure for 24hrs.
9. Lenticulars are then sewn onto the shirt.
10. Clothing tag is glued and then stitched onto shirt using the James Deans stitching pattern.
11. Shirts are run through the Washer and Dryer.
12. FINISHED.
1. Two screens are coated with emulsion and exposed to UV for two minutes and 15 seconds, then pressure washed. This process required multiple attempts for correct exposure of small details.
2. Shirts are ironed and screen printed with one color on the front and back using Speedball fabric ink.
3. Shirts are left to dry for an hour and then heat pressed at 320 degrees Fahrenheit for 12 seconds.
4. SUPACOLOR HEAT TRANSFERS are prepared by hand cutting with a razor.
5. Shirts undergo a pre-press at 320F for 5-8 seconds.
6. The heat transfer is applied and pressed at 320F for 15 seconds.
7. Shirts are cured at 320F for 8 seconds.
8. Shirts are run through a washer and dryer.
*Supacolor description of their heat transfer technology* *On the front end, we use the very best digital offset press technology to print every color except white. These half-million-dollar presses are set up with seven colors (cyan, magenta, yellow, black, violet, orange and silver), giving us a broad spectrum of colors that are unmatched in the industry.  They’re made with water-based inks and certified OEKO-TEX 100, so you can be confident they’re non-toxic. We finish each heat transfer off with one of three different kinds of adhesives to print on various fabrics. What’s different about Supacolor is that we’ve created unique transfers specifically suited for different materials. Why? Because we want our transfers to last longer than the products they are applied to. It doesn’t matter if it’s t-shirts, sweaters, caps or bags. Supacolor’s formula is designed to make the transfer look good for as long as possible. They guarentee 70 washes no fading or cracking*
PRODUCTION TIME: APPROX 45 MINS per hat for this batch (Drying/Curing is not factored into approx time).
1. VINYL CUT LENTICULAR lining.
2. Lenticulars cut by hand to size.
3. Fabric lining is then glued, clamped and left to cure for 24 hrs.
4. EXCESS GLUE REMOVAL OF LENTICULARS.
5. Lenticular Glued and clamped onto hats (left to cure for 24hrs).
6. Lenticular sewn on to hats.
7. FINISHED.


SIZING:
ONE SIZE FITS MOST
MATERIAL
**100% Polyester**
**Structured**
**Firm Front Panel**
- 5 panel cap
- Seamless Foam Front Panel with Lining
- Slight Curved Visor
- 6 Rows Stitching on Visor
- Matching Fabric Undervisor
- Matching Color Sweatband
- Plastic Adjustable Snap
- Size: OSFM - Adult (58cm/22.8")

Garment Dye:
Reinforced Seams
100% USA Cotton
255-265gsm / 7.5oz/ yd²
3.5% Lycra ribbing
Made In USA

SIZING:
Large:
BODY LENGTH (measured from highest point of shoulder): 29.5 in
CHEST WIDTH: 26.5 in
UPPER SLEEVE LENGTH (shoulder to cuff seam): 10.25 in

MATERIALS:
6.5oz
215-225gsm
100% USA COTTON
Sizing:
LARGE
CHEST WIDTH: 22.5 in
BODY LENGTH: 30.5 in